Austenitic mirror finish 18% chromium 8% nickel composition stainless steel plate

304 Structural Stainless Steel Sheet , Mirror Finish Stainless Steel Sheet 4x8 DecorativeContinuous casting slab or slab slab is used as raw material, heated by step heating furnace, dewatered by high pressure water and then into rough rolling mill.The rough rolling material passes through the cutting head and tail and then ente

Featured Products

304 Structural Stainless Steel Sheet , Mirror Finish Stainless Steel Sheet 4x8 Decorative

Continuous casting slab or slab slab is used as raw material, heated by step heating furnace, dewatered by high pressure water and then into rough rolling mill.

The rough rolling material passes through the cutting head and tail and then enters the finishing mill to carry out computer controlled rolling. After the final rolling, it is subjected to laminar cooling (computer controlled cooling rate) and coiler winding, which becomes a straight hair roll. The head and tail of the straight hair roll are often in the shape of a tongue and a fishtail. The thickness and width are poorly accurate, and the side has frequent defects such as a wave shape, a folded edge, and a tower shape. The weight of the coil is heavier and the inner diameter of the coil is 760 mm.
 
Hot rolled plate
Specification
(Thick)
Big DeviationNormal DeviationSmall DeviationNo Deviation
3.0mm2.6mm-2.75mm2.75mm-2.85mm2.86mm-2.9mmno less than 2.9mm
4.0mm3.5mm-3.6mm3.6mm-3.75mm3.76mm-3.95mmno less than 3.95mm
5.0mm4.5mm-4.6mm4.6mm-4.75mm4.75mm-4.95mmno less than 4.95mm
6.0mm5.4mm-5.6mm5.6mm-5.75mm5.75mm-5.85mmno less than 5.85mm
8.0mm7.3mm-7.5mm7.5mm-7.65mm7.65mm-7.85mmno less than 7.85mm
10.0mm9.2mm-9.3mm9.3mm-9.6mm9.6mm-9.85mmno less than 9.85mm
12.0mm11.1mm-11.2mm11.2mm-11.6mm11.6mm-11.85mmno less than 11.85mm
14.0mm13.1mm-13.2mm13.2mm-13.6mm13.6mm-13.85mmno less than 13.85mm

Hot-rolled sheet has relatively low strength, poor surface quality (low oxidation/smoothness), but good plasticity, generally medium and heavy plate, cold-rolled sheet: high strength, high hardness, high surface finish, generally thin sheet, can be used as stamping With the board.

Hot-rolled steel sheet, mechanical properties are far less than cold processing, second only to forging, but with good toughness and ductility

 

Heat Resistance :

Grade 430 resists oxidation in intermittent service up to 870°C and to 815°C in continuous service. This grade may become brittle at room temperature after prolonged heating in the 400-600°C range. This effect can be eliminated by annealing.

304 stainless steel chemical composition
GradeCSiMnCrNPSNi
304≤0.12≤0.75≤1.0016.00~18.00-≤0.040≤0.03≤0.60
 
304 physical properties
304Density :7.75g/cm3
Melting point:1427ºC
Tensile Strength:σb (MPa)≥450
Yield strength :σ0.2 (MPa)≥205
 
304 Chemical composition
CSiMnCrNiSP
0.15≤1.0≤1.011.5~13.5 ≤0.03≤0.04
 
304 Chemical composition
CSiMnCr
0.15≤1.0≤1.011.5~13.5
mechanical properties
Tensile strength σb (MPa)Conditions yield strength 0.2 sigma (MPa)Elongation % (min)Hardness
26047030≤210HV

Welding
Excellent weldability by all standard fusion and resistance methods, both with and without filler metals. Heavy welded sections in Grade 201 require post-weld annealing for maximum corrosion resistance.

Machining
Stainless steel tends to work harden if machined too quickly. For this reason low speeds and constant feed rates are recommended.

Austenitic Mirror Finish 18% Chromium 8% Nickel Compostion Stainless Steel Sheet
Austenitic Mirror Finish 18% Chromium 8% Nickel Compostion Stainless Steel Sheet
Austenitic Mirror Finish 18% Chromium 8% Nickel Compostion Stainless Steel Sheet
Austenitic Mirror Finish 18% Chromium 8% Nickel Compostion Stainless Steel Sheet
Austenitic Mirror Finish 18% Chromium 8% Nickel Compostion Stainless Steel Sheet
Austenitic Mirror Finish 18% Chromium 8% Nickel Compostion Stainless Steel Sheet


FAQ
Q1. How long can make delivery?
A: For stock products,will make shipments in 2-5 days after receiving deposit or receiving T/T;
for products need new production for common materials,usually make shipments in 7-10 days;
for products need special and rare materials,usually need 15-20 days to make shipment.


Q2. Can you provide the samples?
A:Samples can be provided with samples' charge and courier fee by the buyer's side.

Q3. What's your payment terms?
A: Down payments 30%TT and balance 70% TT or L/C.

Q4. How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or TNT. It usually takes 3-5 days to arrive.
Airline and sea shipping also optional.
For mass products, ship freight is prefered.


Q5. Can you accept customize?
A: Yes. It can be customized as per the customers' request.

Q6. How to ensure the quality?
A:Mill Test Certificate is supplied with shipment.
If needed, a Third Party Inspection is acceptable or SGS.

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours