Sensor Integrity Ensures Temperature Measurement Accuracy

2022-06-18 17:58:19 By : Mr. Jack Zhang

Whether measuring or controlling temperature, it begins with the sensor. Better sensors make better process measurements. This feature originally appeared in the May 2022 issue of InTech Focus Temperature & Pressure.

Although not every temperature application is a high-accuracy mea¬surement, best practices can be applied to eliminate sensor drift at the start of an installation. This helps users achieve optimal results while avoiding downtime or troubleshooting that might result from future drift during operation. Several factors influence temperature system accuracy: individual sensor accuracy, extension wire, and measuring devices. When embarking on a project involving temperature measurement or control, consider these basic rules of thumb:

The most common temperature sensors acceptable for temperature measurement and control include thermocouples, resistance temperature detectors (RTDs), thermistors, and semiconductorbased sensors. Only T/Cs, RTDs, and remote input/output (I/O) are discussed here.

Thermocouples (T/Cs) are the most common temperature measurement sensors used in the U.S. for process control. T/C use is a proven technology in industry. They are rugged, relatively inexpensive, and easy to use. Figure 1: Solid sheath RTD or thermocouple temperature sensors. When metals of different composition come into contact, they form a junction that produces a voltage in the millivolt range. If the temperature to which this junction of dissimilar metals is exposed changes, there will be a corresponding change in the millivoltage produced by the junction.

Theoretically, any two different types of conductive material could be used to make a thermocouple. However, only a few combinations are used. The criteria for the material combinations chosen for use in thermocouples include the magnitude of their relative Seebeck coefficient, chemical stability, metallurgical stability, strength, ductility, and cost. There are eight standard thermocouple types established in the U.S. The American National Standards Institute (ANSI) assigned letter designations to these eight types: T, J, K, E, N, S, R, and B (Table 1). The designations are based on the voltage versus temperature relationship for these thermocouples. The designations are not based on their compositions. T/Cs built to the ASTM E230 standard are more accurate. The ASTM E320 standard governs thermocouple accuracy.

Thermocouple sensors built to the ASTM E230 standard are more accurate. The ASTM E320 standard governs thermocouple accuracy, as shown below in Table 2.

Thermocouples can be constructed with premium- or special-grade wire that cuts uncertainty in half. The premium/special designation indi¬cates that this wire has a higher purity alloy mix. Even with premium/special grade T/C, Moore Industries recommends using RTDs instead of T/ Cs whenever possible, as their accuracy, repeatability, and stability are superior to those of T/Cs. In comparing the accuracy data between Table 3 and Table 2, notice that the uncertainty is cut in half by using premium-grade sensors. If T/Cs must be used, premium grade offers greater stability at a negligible cost difference. The problem consistently seen in thermocouples is wire contami¬nation. As contamination occurs, error gradually increases to a point necessitating sensor replacement.

Anytime T/C extension wire is connected to a T/C, it introduces more uncertainty to the measurement (Table 4). If T/C extension wire will be exposed to temperatures outside the specified ranges, consider using actual thermocouple wire instead. In addition to uncertainty, T/C extension wire is susceptible to radio-frequency interference (RFI) and electromagnetic interference (EMI). Extension wire for J and K thermocouple types adds another ±2.2°C (±4.0°F) uncertainty when wire is clean and uncontaminated. Also, T/C extension wire tends to behave as an antenna for RFI and EMI. Use best practices to keep disruptive noise out of these low-level mV signals. T/C extension wire will degrade to the point of replacement; replacing it with more extension wire perpetuates the T/C extension wire replacement loop. However, premium-grade T/C extension wire cuts the potential error in half and should be selected. If extension wire is stressed by being exposed to temperatures outside the limits shown in Table 3, uncertainty will grow. Premium-grade extension wire still allows the possibility of error once metals become contaminated by airborne influences. It is recommended that T/C extension wire be eliminated as close to the T/C as possible by installing either temperature transmitters or remote I/O.

Options exist that allow the elimination of T/C extension wire, thereby taking a step in ensuring reliable measurements. Among the options are temperature trans¬mitters, which can pose cost considerations, and remote I/O. Temperature transmitters, remote I/O, and temperature concentrator modules eliminate expensive T/C and RTD extension wire and other point-to-point wires by sending temperature measurements, process monitoring, and control signals between the field and control room on one digital communication link. Related technologies, such as temperature concentrator modules (TCMs) and temperature transmitter/signal converters, have programmable inputs configurable for RTD, T/C, Ohms, mV or potentiometer, and current or voltage, depending on the specific module type. Outputs would often support HART, PROFIBUS PA, FOUNDATION Fieldbus, MODBUS RTU, etc.

Figure 2: Complete temperature assemblies using the WORM flexible sensor and an infinite combination of materials and components.

RTD wire is a pure material, typically platinum, nickel, or copper. The material has an accurate resistance/temperature relationship, which is used to provide an indication of temperature. RTD elements are normally housed in stainless steel protective probes insulated and isolated from protective sheath with magnesium oxide. Common RTD sensing elements constructed of platinum, copper, or nickel have a repeatable resistance versus temperature relationship (R versus T) and operating temperature range. The R versus T relationship is defined as the amount of resistance change of the sensor per degree of temperature change. The relative change in resistance (temperature coefficient of resistance) varies only slightly over the useful range of the sensor.

Moore Industries thermally ages all of its RTDs to minimize drift once they get into the field. The RTDs are temperature cycled for 1,000 hours at 0° and 600°C, and will maintain accuracy for more than five years. Typically, only Class A sensors are thermally aged. Just as it is recommended that you use premium-grade T/C wire for thermo¬couple measurements, it is also suggested that you upgrade to Class A RTD sensors, which cuts uncertainty in half.

When a particular application demands the highest accuracy possible, Moore recommends ordering a temperature measurement system with bath calibration. A Class A RTD sensor is calibrated in a bath to calibrate it to the transmitter or remote I/O measuring device. This process eliminates the final “as-built” offset error that exists in every sensor. You then receive a NIST-traceable calibration report that indicates the combined sensor and temperature transmitter uncertainty, which is typically better than ±0.01°F. Figure 3: The WORM RTD or thermocouple temperature flexible sensors with flex armor or stainless-steel braid covering the insulating jacket.

The 1,000 Ω platinum RTD “secret.” If you must stay with 3-wire RTDs and you have long leads back to the DCS, consider replacing 100 Ω Pt RTDs with 1,000 Ω Pt RTDs. When this is done, the error caused by the resistance imbalance in the lead wire is reduced by a factor of 10. Figure 4: By replacing 100 Ω Pt RTDs with 1,000 Ω Pt RTDs, the error caused by the resistance imbalance in the lead wire is reduced by a factor of 10.

To optimize measurement performance and minimize long-term maintenance expenses, use the following guide for sensor selection:

All temperature measurements, whether used for temperature indication or process control, begin with the sensor. Thermocouples and RTDs are the most common temperature sensors used in industrial applications. Temperature transmitters, remote I/O, and temperature concentrator modules eliminate expensive T/C and RTD extension wire and other point-to-point wires by sending temperature measurements, process monitoring, and control signals between the field and control room on a digital communication link. Refer to Moore Industries Temperature Reference Guidebook for more information. This feature originally appeared in the May 2022 issue of InTech Focus Temperature & Pressure.

Gary Prentice is vice president of sales at Moore Industries. He manages all of the company’s sales activities and responsibilities, including direct sales management of Moore Industries’ international offices located in the United Kingdom, Belgium, The Netherlands, China, and Australia.

Check out our free e-newsletters to read more great articles..

©2020 Automation.com, a subsidiary of ISA